1pc DC-DC 36V 48V 60V 72V 80V 100V to 24V Converter LED Light Power Supply 20A 30A Module 30-120V to 24V Step-down(24V 25A,30-72V_24V) | 24V 25A,30-72V

ConvertersParameter DescriptionModule nature: step-down module (non-isolated)Power supply name: 36V 48V 60V 72V 80V 100V to 24V 20A ~ 30A (you can purchase the appropriate current according to your own equipment needs)Input wide voltage: 30~120VRated output: 24V (±0.25)Conversion efficiency: 92~96% (efficiency is related to input, output voltage, current, pressure)Waterproof grade: IP67Working environment temperature: -20~+85 (please strengthen the heat dissipation if the ambient temperature is too high)Shell material: aluminum profile shell pottingMaterial: epoxy resin pottingSize: 100*80*39mmWire specification: 13cm (pure copper)Product weight: 500GAfter receiving the converter, you can use a multimeter or voltmeter to measure whether the voltage at the output of the converter is correct. If the voltage is normal, you can supply power to the electrical appliance. Please strictly follow the following wiring methods for wiring.User's ManualDC-DC 36V 48V 60V 72V 80V 100V to 24V Converter LED Light Power Supply 20A 30A Module 30-120V to 24V Step-downPrecautions (Uncertain installations, please contact our company before installation)!!!Long-term use cannot be fully loaded, please reduce power or choose more powerful products, best 50% of maximum power.1. Make sure that all the polarity is correct, and the anti-negative conversion converter (except for input tape reverse protection)2. Make sure the cable is pure copper wire, the input and output cables cannot exceed 2 meters, and the output will be removed by more than 2 meters. The voltage will be reflected. If the line is extended, you need to increase the line diameter according to the corresponding multiple.3. The cable needs to be connected to the thread, please refer to the wire diameter size and securely connected.4. The input terminal is required to connect the fuse or air switch, and you need to select the corresponding fuse or switch] (except the input belt fuse)5. Make sure the battery capacity is large enough to provide sufficient energy. If the input energy is not enough, the voltage will be reduced.6. Make sure the installation environment is well ventilated, so as not to protect over temperature protection, limit current output7. Cannot connect directly to solar panels or wind wind turbines8. Non-charged models cannot be charged battery and lithium batteries9. When connecting the input test with power supply, the input should not exceed the voltage range of the battery, and no overvoltage protection (can be ).Installation step (four lines or four / five terminals)1. Turn off all power supplies and load switches2. Before the wiring, pay attention to all positive and negative poles3. Connection (OUTPUT-) to load negative, connection (OUTPUT +) to load positive4. Connect the fuse or air switch to (Input +) input the positive cable, then connect (Input +) to the battery positive, connect (Input-) to the battery negative electrode5. Make sure all positive and negative connections are correct (do not reverse, reverse the burnback converter), turn on the power and load switch(Note: If the ACC port is connected, connect the ACC to the ignition switch: If you do not need to use the ACC function, connect the ACC to the (Input +) battery "positive.)troubleshooting1. Output no voltage, please check if all lines are connected firm, the battery is enough, whether the fuse is burning.2. Output the voltage, check if the load start current is too large, the ventilation is good, whether the outer casing is heated, whether the cable and the thread are selected and installed, whether it is less than 2 meters, and the input battery has sufficient energy.==========Hign-concerned Chemical : NoneOutput Current : 20A 25A 30AOutput Frequency : 98HZModel Number : JDL...Output Power : 480W600W720WWeight : 500GType : DC/DC ConvertersOutput Type : SINGLESize : 100*80*39MM

• Converters
• 1pc DC-DC 36V 48V 60V 72V 80V 100V to 24V Converter LED Light Power Supply 20A 30A Module 30-120V to 24V Step-down